Quarterly Journal of the Japan Welding Society |
Vol. 22 No. 2 May 2004 |
Contents |
|
|
| Assessment of Hot Cracking Initiation by Laboratory Test Procedures and FEM-Simulation
Associated Experimental Measurements During Welding of Large Weld |
cc |
Horst HEROLD,
Alexandre PCHENNIKOV,
Margot STREITENBERGER |
cc 211 |
|
| GHTA Welding Phenomena of an Aluminum Alloy in Vacuum |
cc |
SUITA Yoshikazu,
NAGAI Hirokazu,
SHINIKE Shuhei,
TSUKUDA Yoshiyuki,
TERAJIMA Noboru,
FUJISAWA Shoichiro,
MASUBUCHI Koichi,
IMAGAWA Kichiro
and YAMASHITA Masahiro |
cc 218
|
|
Modeling of Short-circuiting Transfer Process in GMA Welding
|Numerical Model of Metal Transfer Phenomena in GMA WeldingiReport 1j| |
cc |
HIRATA Yoshinori,
OSAMURA Takafumi,
ONDA Masahiko,
ANDO Naoko
and OHJI Takayoshi |
cc 224 |
|
Effect of Inner Diameter on Friction Torque in Friction Welding of Pipes@ |
cc |
KIMURA MasaakiC
KUSAKA MasahiroC
SEO Kenji
and FUJI Akiyoshi |
cc 233 |
|
| Solutions to Problems of Tiny Spatter and Arc Interruption in AC Pulsed MIG Arc Welding |
cc |
TONG Hongjun
and UEYAMA Tomoyuki |
cc 240 |
|
Melting and Cutting Behavior of the Bundle of Fine Cu Wires
|Study on Uniform Melting of the Bundle of Cu Wires by YAG Laser i2nd Reportj| |
cc |
SASAKI Shoji,
OGUMA Masaomi,
TAGASHIRA Kohsuke
and ORIKAWA Makoto |
cc 248 |
|
Observation of Bond Interface of Al/Ti Clad Material by Transmission Electron Microscopy
|Development of Clad Materials by Vacuum Roll Bonding and its Characteristics iReport 4j| |
cc |
NISHIO Kazumasa,
KATOH Mitsuaki,
YAMAGUCHI Tomiko,
ERA Hidenori
and SAKAMOTO Kenichi |
cc 254 |
|
Microstructure of the Hyper Interfacial Bonded Layer of Ultra Fine-Grained Steels
|Study on the Hyper Interfacial Bonding of Ultra Fine-Grained Steels iReport 2j| |
cc |
JEONG BoyoungC
NISHIMOTO Kazutoshi
and SAIDA Kazuyoshi |
cc 261 |
|
Influence of Hot Dip Galvanizing Conditions and Steel on Fatigue Strength
|Fatigue Strength of Welded Joints by Hot Dip GalvanizingiReport 3j| |
cc |
MORI Takeshi,
MINAMI Kuniaki,
HORIKAWA Hidenobu |
cc 272 |
|
| Applicability of the Critical Condition for Ductile Cracking of Linepipe Steel to the Evaluation
of Ductile Cracking of an Axially Notched Linepipe |
cc |
KAWAGUCHI Shinobu,
OHATA Mitsuru,
OKI Yusuke, OGITA Gen, HAGIWARA Naoto
and TOYODA Masao |
cc 282 |
|
Microstructural Observation on the Bond Interface in A3003/SUS304L Clad Material
|Characteristics of the Bonded Zone in A3003/SUS304L Clad Material @@ Produced Using Vacuum Roll BondingiReport 1j| |
cc |
KAWANO Takayuki,
MATSUI Masakazu,
NISHIO Kazumasa,
KATOH Mitsuaki
and HIRATA Masahiro |
cc 291 |
|
Effect of Heat Treatment on the Bond Interface Structure of A3003/SUS304L Clad Material
|Characteristics of the Bonded Zone in A3003/SUS304L Clad Material @@ Produced Using Vacuum Roll BondingiReport 2j| |
cc |
KAWANO Takayuki,
MATSUI Masakazu,
NISHIO Kazumasa,
KATOH Mitsuaki
and HIRATA Masahiro |
cc 300 |
|
| Welding between ADC12 and SS400 by Means of Friction Stirring |
cc |
FUKUMOTO Masahiro,
TSUBAKI Masami,
SHIMODA Yoichiro
and YASUI Toshiaki |
cc 309 |
|
Brazability of Aluminum Alloy to Steels using Aluminum Filler Metal
|Dissimilar Laser Brazing of Aluminum Alloy and SteelsiReport 1j| |
cc |
SONG Woohyun,
SAIDA Kazuyoshi,
ANDO Akiyoshi
and NISHIMOTO Kazutoshi |
cc 315 |
|
Feature Extraction of Pb Free Solder Fillet Profile by an Image Processing Taking
the Profile Scattering into Consideration |
cc |
ASAKURA Yoshihiro
and TAKAHASHI Yasuo |
cc 323 |
|